Serving the Birmingham area  ·  (205) 946-3891  ·  Open Mon-Sun 7am-7pm
📞 (205) 946-3891 Free Quote

Metal Roofing in Vestavia Hills, AL (35216) · Local Professionals

Birmingham Metal Roofing · Fast response in Vestavia Hills and the Birmingham area · Free estimate 24h

✅ Metal Roofing Alliance Member 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+310Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured✅ Metal Roofing Alliance Member

Vestavia Hills sits up on the ridge, and the wind up here lets you know it. From the brick ranches off Rocky Ridge Road to the two-story homes stepping up the hills near Liberty Park, roofs in 35216 take a beating that flatland neighborhoods never see.

When a storm rolls through Dixie Alley, we get calls from homeowners near Vestavia Hills Elementary and around Wald Park who have shingles peeled back or a metal panel lifted at the seam. We are Birmingham Metal Roofing, and we have been climbing these roofs long enough to know exactly where the wind hits first.

Metal Roofing in Vestavia Hills (35216)

The terrain here is the whole story. Lots on the ridge slope hard, and water runs fast toward the foundation when a downspout or gutter fails. We see a lot of homes built in the 1960s through the 1990s with steep pitches and tight side yards, plus newer construction up near the Summit where the rooflines get complicated. On the wooded lots, oak limbs and pine cones are a constant threat to fasteners and panel edges. Standing seam is a natural fit for these homes because it handles wind uplift better than exposed-fastener panels, and the hidden clips mean fewer places for water to get behind the metal. For the older brick homes closer to Shades Mountain, we often recommend stone-coated steel that matches the original architectural look while giving you the hail resistance the asphalt shingles never had.

Our team has worked across Vestavia Hills and the surrounding Birmingham area for years, and we know how the ridge wind behaves after a front moves through. We are a Metal Roofing Alliance member and fully insured with general liability and workers' compensation, so your property is covered while we are on it.

Our services in Vestavia Hills

How a Job Works in Vestavia Hills

Step 1: You call us at (205) 946-3891, and we set up a free on-site assessment. We walk the roof, check the flashing and fasteners, look at the attic if you have one, and give you a written estimate with the scope spelled out. No pressure, no surprise line items.

Step 2: Once you approve, we pull the roofing permit through the local building department. In Vestavia Hills, that means checking with the City of Vestavia Hills website for the current requirements, and we handle that step for you. On tight lots near Columbiana Road or in the older neighborhoods, we stage materials carefully so we are not blocking your neighbor's driveway. If your home is in an HOA or a historic overlay, we coordinate the design review before we order panels, because color and profile have to be approved first.

Step 3: Cleanup is part of the job, not an afterthought. We magnet-sweep the yard and driveway for nails, haul off all old material, and walk the finished roof with you so you can see the seams, flashing, and gutter connections before we call it done.

Pricing in Vestavia Hills depends on the roof size, the pitch, how many layers are coming off, and how tight the access is. As a ballpark, metal roof installation starts at $8 per square foot, standing seam starts at $10, metal roof replacement starts at $9, and a retrofit over existing shingles starts at $7. Repairs and leak calls start at $450, screw replacement and re-fastening starts at $750, and flashing or chimney work starts at $600. Coating and painting starts at $2.50 per square foot, and gutters for metal roofs start at $9 per linear foot. Storm and wind damage inspections are free. The biggest cost factors are square footage, roof complexity, and whether we are tearing off or going over. Call (205) 946-3891 for a free estimate that fits your actual roof.

✅ Metal Roofing Alliance Member, licensed and insured for work in Vestavia Hills and nearby areas.

My house is on a steep lot near Shades Mountain and the lower roof gets hammered by wind. What metal roof holds up best there?
On exposed ridge lots, we usually steer homeowners toward standing seam with concealed fasteners. There are no screws showing to back out or leak, and the panels are rated for high wind uplift. We also check the eave and ridge details, because that is where wind gets underneath and peels a panel.
A storm just took off some shingles near Wald Park. How fast can you get out to look at it?
Call (205) 946-3891 and we will schedule a free storm damage inspection as soon as we can get on the roof safely. We document what we find with photos, make temporary repairs if water is getting in, and give you a written scope for the permanent fix.
What does a typical metal roof replacement cost for a 2,000 square foot home in 35216?
For a home that size, most replacements land somewhere between the low teens and the low twenties depending on pitch, access, and whether we tear off the old roof. Standing seam runs more than corrugated panel. We give you a firm number after we see the roof, not a phone guess.
Do I need a permit to replace my roof in Vestavia Hills?
Yes, a full replacement or re-roof typically requires a permit, and the rules on layers, inspections, and fees are set by the local jurisdiction. We pull the permit for you and confirm the current requirements with the City of Vestavia Hills website before we start.
My HOA wants to approve the roof color. Can you help with that process?
We deal with HOA design review regularly in Vestavia Hills. We can provide panel samples, color chips, and specification sheets for the board, and we will not order material until you have written approval. If there is a property line question about overhang or drainage, we flag it early so you can talk to your neighbor before work begins.
Are you covered by insurance if someone gets hurt or something gets damaged on my property?
Yes. We carry general liability and workers' compensation coverage, and we are fully insured. We are happy to provide a certificate of insurance before we start so you have it on file.
What maintenance should I do on a metal roof in Vestavia Hills to get ahead of storm season?
Have the roof inspected once a year, ideally in early spring before tornado season. We check fasteners, sealant at penetrations, and the gutter system, because clogged gutters on a steep ridge lot send water straight to the foundation. After any hail or high wind event, a quick look at the panels and seams can catch a small issue before it becomes a leak.
Why choose us?

Trusted professionals in Birmingham

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Birmingham

All your work handled by qualified professionals in Birmingham

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

310+ Verified Client Reviews in Birmingham

⭐⭐⭐⭐⭐ 4.9/5 · 310 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Birmingham · Response within 24h · No commitment · ☎ (205) 946-3891

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Birmingham ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm